FAQs
SPN 2659 FMI 18 - Engine Exhaust Gas Recirculation 1 Mass Flow Rate : Data Valid But Below Normal Operating Range - Moderately Severe Level Fault Overview Fault code sets when Engine Control Module (ECM) detects feedback from Mass Air Flow (MAF) Sensor indicating air flow through the engine is above expected setpoint ...
What is the code 2659 on a Freightliner? ›
SPN 2659 is a fault code related to the Exhaust Gas Recirculation (EGR) system. It indicates that the actual EGR flow differs from the expected flow based on the commanded EGR valve position.
What is the SPN 2659 FMI 16 on a Volvo d13? ›
Okay no problem, The SPN 2659 FMI 16 is for egr flow rate above desired. This basically means that the measured egr flow rate at the EGR diff pressure is higher than normal. The most common cause of this fault is either plugged ports at the EGR diff pressure sensor or a defective stuck high diff pressure sensor.
What does spn 102 fmi 18 mean? ›
SPN 102/FMI 18 - GHG14. Description. Intake Manifold Pressure Lower than Expected Under a Load.
What is engine code FMI 18? ›
The SPN 18 FMI 18 code is a diagnostic trouble code for a sensor fault on the engine coolant temperature sensor circuit. This code is typically triggered when the sensor signal is out of range or the sensor is not functioning properly. This code indicates that there is an issue with the cylinder pressure sensor.
What does SPN and FMI mean? ›
SPN is short for suspect parameter number. It identifies which electrical circuit, part or component of your truck isn't working properly. FMI stands for failure mode identifier—this part of the fault code tells you what type of problem your truck has.
What is a shift solenoid code? ›
The P0750 code indicates that the shift solenoid, which is one of the devices that controls the flow of transmission fluid within the unit, has malfunctioned in some way.
What is the code for throttle actuator? ›
The P2100 code definition is “Throttle Actuator 'A' Control Motor Circuit/Open.” This code indicates that your powertrain control module (PCM) or engine control module (ECM) has detected an electrical issue in your throttle actuator control motor circuit, specifically actuator “A,” whichever one happens to be in your ...
What does SPN mean on engine? ›
SPN stands for Suspect Parameter Number. It's a diagnostic trouble code that provides detailed information about specific faults detected by the vehicle's ECU, making it easier to identify and address issues within the vehicle's electronic systems.
What is the failure mode indicator FMI? ›
Failure Mode Indication (FMI), as part of the J1939 standard used in heavy-duty vehicles, functions by closely monitoring system components. When a fault occurs, FMI generates a precise code that identifies the specific nature of the issue, much like an advanced version of a 'check engine' light.
This fault code is for low fuel delivery pressure during cranking. Replace your fuel filters and look for any fuel leaks or restrictions between the fuel tank and fuel pump. Low fuel pressure can also be caused by a faulty fuel pump, injectors,or pressure regulator.
Why is my intake manifold pressure low? ›
It's likely the piston rings are being worn down and allowing excess fuel/air mixture into the intake, reducing efficiency. In a situation where the manifold pressure starts to slip lower than normal… you have something obstructing your intake valve.
What does FMI error mean? ›
Failure Mode Identifier (FMI) Codes on J1939 data link. The FMI is used along with the SPN to provide specific information that relates to a diagnostic trouble code (DTC). The FMI may indicate that a problem with an electronic circuit or an electronic component has been detected.
How does a boost sensor work? ›
The boost pressure sensor with temperature sensor is installed in the air inlet pipe ("inlet manifold") between the turbocharger and engine, and measures the absolute pressure. Additional consideration for the intake air temperature allows more accurate measurement of the intake air mass.
What is code 2659 on Maxxforce? ›
2659-14 EGR System flow rate error during Air Management Test. Since there's no EGR flow rate faults indicating a bad EGR valve, I would say the EGR cooler is plugged. You will have to pull the doghouse off to remove the EGR valve and check the inlet side of the EGR cooler behind the EGR valve.
What does SPN mean in diagnostics? ›
SPN stands for Suspect Parameter Number. It's a diagnostic trouble code that provides detailed information about specific faults detected by the vehicle's ECU, making it easier to identify and address issues within the vehicle's electronic systems.